Order Link BELOW and also by clicking on STORE from menu. Price $349.99. Note: The end of the first production run is approaching. Once we sell out the remaining units, we will take a few months break while re-order parts and enclosures. We are also evaluating the best course for international resellers or perhaps simply direct ordering from our website for non-US/Canadian customers.
“The Mountain Topper”
The LnR Precision MTR transceivers are designed to be efficient portable CW rigs. Whether climbing a mountain and operating SOTA or just out for an afternoon in the park, the MTR’s small size, light weight and meager battery requirements makes it a great choice for these activities.
- Four bands – 80M, 40M, 30M and 20M
- Very low receiver noise floor
- Low current for maximum battery life
- Wide operating voltage range – 5.5V to 13V
- Full 5W “QRP” gallon with 12.0 Volt supply
- 2 line, back lighted LCD display
- SWR – RF Power display
- Built in Real Time Clock
- Internal Iambic B mode keyer, 5 to 31 WPM in 1 WMP increments.
- Three Morse message memories with beacon mode.
- 80 meter, 40 meter, 30 meter and 20 meter operation.
- Receiver sensitivity : ~ 0.5 uV
- Receiver audio bandwidth: ~ 400 Hz centered at 600 Hz.
- Receiver current: ~ 27 ma
- Transmit output power: 5 watts typical at 12.0 Volt input
- Transmit current: 750 ma Max with 5 watt output
- Transmit spurious outputs: -50 dBc or better
- Supply voltage 5.5 volts minimum, 13 volts maximum. 6 to 12 recommended.
- Antenna Jack: BNC
- Power Jack: 5.5mm with 2.5mm pin
Dimensions: 5.150″ Length x 3.0″ Wide x 1.075″ Thick
Weight: 7.95 oz
Power supply options:
The MTR-4B V2 is designed to put out about 5 watts with a 12.0 V supply. This makes it a good match to a 3S Li-ion pack which produces a bit over 12V when fully charged.
A 2S pack can also be used, with reduced power output. But also with reduced transmit current draw, which will extend battery life. Operation is possible down to the minimum discharge voltage for the cells, about 6V, and still produce over 1 Watt of output power.
A 4S pack produces a bit too much voltage to safely power the rig, but a low dropout regulator can be added to bring the voltage down to one more suitable for the rig.
A 9V smoke alarm battery (once used in transistor radios) can power the MTR-4B for several hours. A tad expensive to do regularly though. But it is fun to see how many contacts you can make using one during a contest sprint. A 9 or 12V battery pack made of AA cells is more long lasting.
A 13.8V bench supply can be used, but this will bring the output power up to 6 to 7 watts. This is fine so long as the SWR is low. At 7 watts, the transmit current is near the maximum the PA FETs can handle and near the point at which the resettable internal fuse will trip (1 A). A high SWR will increase the current in the PA and either trip the fuse or damage the PA.
A simple way of making a 13.8V supply safe to use is to add two silicon rectifier diodes in series with the positive power lead, such as 1N4001 diodes. This will drop the supply voltage to the MTR by about 1.5 volts.
MTR3B_LCD (Production run ended 8/20)
New Mountain Topper redefines Portable CW with a gorgeous LCD screen in a small lightweight enclosure!
The Mountain Topper Rigs are designed to be a very small, light weight, very battery efficient, multi-band CW rig suitable for field operation. The small size and low weight make this rig ideal for SOTA operators and backpackers.
- 3 band operation – 40/30/20
- Wide power supply operation – 6V to 12V
- Low operating current – 20 ma @ 6V, 15 ma @ 12V
- 5+ Watts out at 12V supply, 2.5-3W at 9V supply
- Easy to read 2 line LCD display with back lighting
- Push button tuning and audio limiting eliminates protruding knobs
- Iambic B mode keyer, 9 to 31 WPM range in 1 WPM steps
- Three, 63 character message memories with beacon mode
- Optional decoding and display of Morse being sent via paddle. Know you are sending good code
- Built in 24 hour real time clock
- Battery back up restores last used settings on power up
Production Run Complete
(Potential re-release in 2022)
MTR3b_LCD (8/28/20): We have completed the current production run of the massively popular MTR3b_LCD. The newly re-design of the MTR4b (version 2) contains all the features of the MTR3b_LCD plus additional functions so in many ways it will serve as a replacement of the 3b. However, we acknowledge the lower price point and slightly smaller enclosure. We are considering another run of the MTR3b_LCD, but it will not occur until 2022, if at all.
MTR4b (12/7/20): LNR is working with Steve Weber on a reintroduction of the MTR4b. We are contemplating offering some new features but will announce those once we have confirmation. The COVID-19 situation has lengthened the timeline, but stay tuned to our website or the Facebook Mountain Topper group for information when we make it available.
MTR-SSB development: (12/6/19): We regret to inform that the new MTR-SSB transceiver will not be released as planned. In most simplest terms, there are some technical limitations preventing operations when extending it to the 40M/20M bands. The 80M/60M bands for the emergency communications interest is not affected. The minimalistic nature and outstanding reliability in all of the Steve Weber KD1JV Mountain Topper designs are well documented and will not be compromised which I’m sure everyone appreciates. So while we are all disappointed, we are gauging interest in the 80M/60M version in 2020 and are considering special single band versions as well.
EndFedZ Antennas (Acquisition): LNR is pleased to announce that the PAR EndfedZ line of wire antennas was acquired by Vibroplex in 2019. Customers can purchase these antennas directly at their website at Vibroplex.com. This move is a positive for both companies and we are excited about the future going forward.
W4OP Loop: Unfortunately, as part of our streamlining in 2019, we halted production of the W4OP Loop antennas to devote our entire attention on the very popular Mountain Topper transceiver line. The W4OP (remote and manual controlled versions) are phenomenal antennas and would be a great product line for another company or interested entrepreneur to pick up. If interested, contact LNR.
New Mountain Topper Facebook Group PageMountain Topper Facebook Group Page – Cool customer driven FB page to share stories, pics and general MTR discussion.